Custom Cable Assemblies
One manufacturing partner for M12, M8, FAKRA, RJ45, JST, Molex and MIL-spec connector platforms — built to your drawing, tested before shipment.
- ISO 9001 & IPC/WHMA-A-620 certified manufacturing
- Low-volume, high-mix production — from one prototype to recurring runs
- 100% continuity testing, IP67 sealing and EMI shielding available
Custom Cable Assemblies Built to Your Exact Specification
We manufacture custom cable assemblies for OEMs across industrial automation, robotics, medical equipment, transportation and energy. From a single prototype to a recurring high-mix production run, every assembly is built to your drawing — connector platform, coding, pin count, cable material, shielding, length and labelling — with 100% electrical testing carried out before shipment.
Not sure which platform fits your application? Start with the category that matches your connector, or send us a drawing and we will specify it for you.
Choose Your Connector Platform
Nine dedicated assembly families, each with its own specification range, termination options and testing programme.
M12 Cable Assemblies
A-, B-, D- and X-coded IP67 assemblies for sensors, actuators and industrial Ethernet up to 10 Gigabit.
Learn more
M8 Cable Assemblies
Compact 3-, 4- and 8-pin sensor cables with a threaded locking system for space-constrained installations.
Learn more
FAKRA Cable Assemblies
Colour-coded 50Ω RF assemblies for GPS, camera, radio and telematics wiring.
Learn more
Mini-FAKRA Cable Assemblies
High-density RF connectivity up to 20 GHz in a fraction of the standard FAKRA footprint.
Learn more
MIL-Spec Circular Connectors
Rugged all-metal assemblies built to MIL-DTL-5015, MIL-DTL-26482 and MIL-DTL-38999.
Learn more
IX Industrial Connectors
Cat6A industrial Ethernet in a connector roughly 70% smaller than a standard RJ45.
Learn more
RJ45 Cable Assemblies
Cat5e, Cat6 and Cat6A industrial Ethernet with UTP, FTP, S/FTP and IP67 sealed options.
Learn more
JST Cable Assemblies
XH, VH, PH, SH and GH series in wire-to-board, wire-to-wire and pigtail configurations.
Learn more
Molex Cable Assemblies
Micro-Fit, Mini-Fit and Mega-Fit power and signal assemblies with custom pin-outs and keying.
Learn moreWhat You Get With Every Order
Built to Your Drawing
Connector brand, series, coding, pin-out, wire colour and labelling matched to your BOM — not pulled from a fixed catalogue.
Prototype to Production
Samples first for your validation, then low-volume or high-mix runs with the same tooling, workmanship and inspection standard.
Full Electrical Testing
100% continuity testing as standard, with insulation resistance, dielectric withstand and IP leak testing available on request.
Certified Manufacturing
Produced under ISO 9001 quality management and IPC/WHMA-A-620 workmanship requirements, with RoHS and REACH compliant materials.
Manufacturing Range at a Glance
| Parameter | Available Range |
|---|---|
| Connector Platforms | M12, M8, FAKRA, Mini-FAKRA, MIL-spec circular, IX Industrial, RJ45, JST, Molex |
| Cable Materials | PUR, PVC, TPE, silicone, LSZH, S/FTP industrial Ethernet, RG174 / RG316 |
| Shielding | Unshielded, foil, braided, foil + braided, 360° shield termination |
| Termination | Male to female, male to pigtail, female to pigtail, straight and right-angle |
| Overmolding | Custom tooling, strain relief, colour-matched and branded overmolds |
| Protection | IP67 as standard, IP68 available on request |
| Temperature | -40°C to +105°C (material dependent) |
| Length | 0.2m to 100m, custom lengths on request |
| Testing | 100% continuity; insulation resistance, dielectric withstand, IP leak testing on request |
| Compliance | ISO 9001, IPC/WHMA-A-620, RoHS and REACH |
Quality & Testing
Every assembly we ship is manufactured in accordance with ISO 9001 quality management standards and IPC/WHMA-A-620 workmanship requirements for cable and wire harness assemblies.
Each unit undergoes 100% continuity testing before packing. Additional testing — including insulation resistance, dielectric withstand and IP leak testing — is available on request, with test reports supplied with your shipment.
How Custom Orders Work
Send Your Specification
Share your drawing, BOM, or simply describe the application and environment.
Engineering Review
Our engineers confirm the connector, cable, shielding and length, and flag any risk.
Prototype Approval
We build samples to your specification for validation before production starts.
Production & Delivery
Low-volume or high-mix production, fully tested and packed to your requirements.
Need a Custom Cable Assembly?
Tell us the connector platform, cable specification and length — or just upload a drawing. Our engineers respond within one business day.